- NISSAN DATA SCAN 2 CANNOT CONNECT TO BCM 2004 MAXIAM HOW TO
- NISSAN DATA SCAN 2 CANNOT CONNECT TO BCM 2004 MAXIAM CODE
J1708 is a DLC used on heavy duty vehicles. and were going to include an estimate for your custom repair. The data link connector ( DLC) is the multi-pin diagnostic connection port for automobiles, trucks, and motorcycles used to interface a scan tool with the control modules of a given vehicle and access on-board diagnostics and live data streams. Nissan PickUp The Nissan Navara, also known as the Nissan Frontier in North America and the Nissan NP300 in Mexico and Europe, is a pickup truck that was introduced by Nissan in 1997. If not located beneath the steering column, look for the port in the areas indicated by numbers 4 - 9. Remember that your car or truck might have more than one fuse box.īeside above, how do I find my OBD port? The OBD-II port is usually located under the dashboard, beneath the steering wheel column (1 - 3 in the diagram below). Check your fuses to see if any have gone bad.
NISSAN DATA SCAN 2 CANNOT CONNECT TO BCM 2004 MAXIAM HOW TO
Even a fuse dedicated solely to the car's computer diagnostics can blow for no apparent reason. DIY: Immobilizer Hacking for Lost Keys or Swapped ECU: DIY: ImmobilizerHacking for Lost Keys or Swapped ECUHeres how to reprogram your cars engine immobilizer to program new keys in the invent of lost keys or a swapped ECU.DIY Video: Disclaimer:The engine immobilizer is a security device.
NISSAN DATA SCAN 2 CANNOT CONNECT TO BCM 2004 MAXIAM CODE
The most common reason for getting no OBD code is simply a blown fuse. In respect to this, does the OBD have a fuse? Use a ground other than ECM terminals, such as the ground.Īgain, if you plan to disconnect or reconnect a module, make sure the battery is disconnected first.Usually there is a fuse for the OBD port, if you cannot find they the fuse for the cigarette lighter and the auxiliary ports. Doing so may result in damage to the ECMs transistor. Pulse signal is measured by CONSULT-II.ĬAUTION: Do not use ECM ground terminals when measuring input/output voltage. Specification data are reference values and are measured between each terminal and ground. Data is for comparison and may not be exact.ĮCM Harness Connector Terminal Layout Part 1ĮCM Harness Connector Terminal Layout Part 2ĮCM Harness Connector Terminal Layout Part 3ĮCM Harness Connector Terminal Layout Part 4ĮCM Harness Connector Terminal Layout Part 5ĮCM Harness Connector Terminal Layout Part 6ĮCM Harness Connector Terminal Layout Part 7ĮCM Harness Connector Terminal Layout Part 8ĮCM Harness Connector Terminal Layout Part 9ĮCM Harness Connector Terminal Layout Part 10 Use extreme care not to touch 2 pins at one time. Connect a break-out box (SST) and Y-cable adapter (SST) between the ECM and ECM harness connector. When disconnecting ECM harness connector, loosen it with levers as far as they will go as shown in the figure.Ĥ.
ECM is located in the engine room passenger side behind battery.ģ. Vehicle Powertrain Management Relays and Modules - Powertrain Management Relays and Modules - Computers and Control Systems Engine Control Module Testing and Inspection Pinout Values and Diagnostic Parameters Control Module Pinout Valuesġ.
See the remaining pics.Ģ005 Nissan-Datsun Truck Murano AWD V6-3.5L (VQ35) Once it is disconnected, inspect it for damage to the pins, corrosion, or if one of the pins have been pushed in.Īs far as the ECM, here are all the pinout values for checking. Make sure the battery is disconnected before you disconnect or reconnect modules.įirst, make sure the connector is tight. If you look at pic 1, it shows the location of the BCM.